How To Install A Sink Without Plumdomain_7

Want to install a kitchen sink? This expert guide will take you through the procedure footstep-by-step.

The kitchen sink is an essential element of any household. Food is prepared, dishes are done, flower vases are filled, and nutrient is tending of in the kitchen sink. The kitchen sink can exist installed to a higher place the counter, below the counter, or even as a seamless role of the counter itself.

To many homeowners, installing a kitchen sink seems like a daunting chore, just the fact is, if you can trace around a template and cut out a pigsty, yous tin install a kitchen sink.

Installing a kitchen sink in a plastic laminate countertop is a relatively like shooting fish in a barrel job.

You do want to make certain your new sink fits your countertop and the cabinet below it, so measure out the width and depth of your lower cabinets before making a purchase.

Generally, a sink up to 22 inches deep (from front to back) volition fit in a standard 24-inch-deep cabinet if yous have no backsplash; if you do have a backsplash, your countertop will only take a sink upwardly to 20 i/2 inches deep. Of course, your options will increase if y'all are also changing your cabinetry and countertop.

Install a Drib-In Kitchen Sink: Stride-past-Footstep

To install a counter-elevation kitchen sink, follow the directions below:

+

Notice Pre-Screened Plumbers Most You

1 The showtime step when installing a new sink is to properly site the opening. Most sink manufacturers provide a template.

Position the template so it is centered on the sink cabinet and is at least 1 one/two inches back from the countertop'southward front edge. If your countertop is deeper than 24 inches, identify it further back, but not more than than four inches. Tape the template in place, and so outline it with a marking.

Lay the sink's template on the countertop and mark for the cutout.

2 After marking the opening, remove the template and drill a 3/8-inch-diameter hole in each corner.

Insert a saber-saw blade in 1 of the holes and kickoff cutting along the inside of the line. To prevent the cutout from snapping off and falling through as y'all consummate the cuts, showtime screw a scrap of forest from front to back on the top of the cutout long plenty so information technology spans the opening, plus a couple of inches.

When you've finished, simply lift the cutout from the template.

Utilise a saber saw to cut out the template area.

3 Install the faucet (encounter How to Install a Kitchen Faucet for instructions) and the sink strainers. (Doing this when you've got full access to the sink will be much easier than plumbing equipment the pieces in from below after the sink is installed.)

Next, to create a watertight seal between the sink and the countertop, employ a bead of silicone caulk or plumber's putty around the entire perimeter of the underside of the sink'due south lip.

Seal the underside of the sink'south flange before setting the sink in place.

4 Carefully flip the sink over and insert into the opening, taking care non to disturb the caulk or putty.

Now install the kitchen sink. If your sink is heavy, go help lifting and installing it; also consider placing a couple of scraps of wood nigh the border of the opening to support the sink and protect your fingers as you lot drop it into position.

Afterwards installing the faucet onto the sink, position the aggregation in the cutout.

v Most sinks are pulled down tight against the countertop with special mounting clips that hook onto the lip on the underside of the sink and are tightened with a screwdriver or nut-driver. Follow the manufacturer'due south directions for spacing these clips.

Tightening the mounting clips may cause the caulk or putty to squeeze out from nether the sink lip, so remove this backlog with a clean, soft rag.

Secure the underside of the sink to the countertop past tightening the bolt clips.

6 To consummate the project, first connect the P-trap. Join the faucet lines to the hot and cold supply lines with flexible supply tubes and connect the strainers to the waste line.

Turn the h2o on at the shut-off valves, remove the aerator from the faucet, and then turn on the water from the faucet to flush the system. Reinstall the aerator after you've run the water for a minute or so.

Install the P-trap below the sink and the h2o supply tubes to the faucet.

Install a Driblet-In Kitchen Sink Video

This video walks you through the steps of installing a drop-in kitchen sink.

Install an Under-Mount Kitchen Sink Video

Installing an under-mount kitchen sink is quite as piece of cake equally installing a drop-in sink. Nevertheless, this video shows you how:

Featured Resource: Get a Pre-Screened Local Sink Installation & Plumbing Pro

Telephone call for free estimates from local pros now:
1-866-342-3263

Source: https://www.hometips.com/diy-how-to/install-kitchen-sink.html

Posted by: hopkinsmusen1966.blogspot.com

Share this post